Router Ubiquiti Networks ERPro‑8

Here you find how to configure and reset Ubiquiti Networks ERPro‑8 Router.

Ubiquiti Networks ERPro‑8

Preconfigured wireless settings

SSID:
On a sticker on the router’s case
Password:
On a sticker on the router’s case

Accessing your router's configuration interface

To connect to your router's web interface, follow these steps:

  1. Switch on router
  2. Establish a connection between the device and the router via network cable
  3. Open browser
  4. Enter IP address in the address bar and then confirm with ‘Enter’ key
  5. Enter username as well as password in the login form and confirm

Reset Ubiquiti Networks ERPro‑8 router to factory defaults

To reset the Ubiquiti Networks ERPro‑8 to its default settings, you have to do the following steps:

  1. Put router into operation
  2. For at least 10 seconds, press the RESET button
  3. Device restarts automatically
  4. Default settings have been restored

The unit will reboot automatically. Once the power light stops blinking, the unit has been reset and is ready to use. Resetting the router does not reset the firmware to an earlier version, but it will change all settings back to factory defaults.

Ubiquiti Networks ERPro‑8 Router Security

Change Ubiquiti Networks ERPro‑8 Default Wifi Name (SSID)

Rename your Ubiquiti Networks ERPro‑8 Default Wifi Name (SSID). Some Ubiquiti Networks routers come with default network names (with the name of the manufacturer). We recommend to use a different name because a default name unnecessarily identifies the make of your router, making it easier for attackers to break in.

Change Ubiquiti Networks ERPro‑8 Default Password

It’s easy for a hacker to find out the manufacturer’s default password for your Ubiquiti Networks ERPro‑8 router and then use that password to access your wireless network. So it’s wise to change the administrator password for your Ubiquiti Networks ERPro‑8 router. When you’re deciding on your new password, try to pick a complex series of numbers and letters and try to avoid using a password that can be guessed easily.

MAC Address filtering for Ubiquiti Networks ERPro‑8 router

MAC filtering allows you to limit access to your Ubiquiti Networks ERPro‑8 router. To enable this feature, enter into your Ubiquiti Networks ERPro‑8 router the 12-character MAC ID of each computer that will connect to your network. Be sure to update this information if you add or remove devices.

Disabling Broadcast SSID for Ubiquiti Networks ERPro‑8 router

Ubiquiti Networks ERPro‑8 router transmits your Wi-Fi network ID (the so-called SSID) to everyone. This may be changed at will by unchecking the corresponding box in the settings. Then your network will not be so easily hacked. However, as a compromise, you will have to enter the SSID every time that you connect a device to the network. This step is not mandatory.

MAC Address filtering for Ubiquiti Networks ERPro‑8 router

MAC filtering allows you to limit access to your Ubiquiti Networks ERPro‑8 router. To enable this feature, enter into your Ubiquiti Networks ERPro‑8 router the 12-character MAC ID of each computer that will connect to your network. Be sure to update this information if you add or remove devices.

Where are you placing the Ubiquiti Networks ERPro‑8 router in the house?

You wouldn’t think about this at first, but where you place your Ubiquiti Networks ERPro‑8 also has a bearing on your security.

Place the Ubiquiti Networks ERPro‑8 router as close as possible to the middle of your house. The first benefit is that all the rooms in your house have the same access to the Internet. The second benefit is that you don’t want to have your wireless signal range reach too much outside your house, where it can be easily intercepted by cybercriminals.

For this reason, don’t place your Ubiquiti Networks ERPro‑8 router next to a window, since there’s nothing to obstruct the signal going outside your house.