Router PLDT SpeedSurf 504AN

Here you find how to configure and reset PLDT SpeedSurf 504AN Router.

PLDT SpeedSurf 504AN

Preconfigured wireless settings

SSID:
On a sticker on the router’s case
Password:
On a sticker on the router’s case

Accessing your router's configuration interface

To connect to your router's web interface, follow these steps:

  1. Turn on router
  2. Establish a connection between the device and the router via network cable or Wi-Fi*
  3. Open web browser
  4. Enter IP address in the address bar and then confirm with ‘Enter’ key
  5. Enter username and password in the open interface and confirm once more

Reset PLDT SpeedSurf 504AN router to factory defaults

To reset the PLDT SpeedSurf 504AN to its default settings, you have to do the following steps:

  1. Turn on router
  2. Press Factory Reset button and hold for at least 15 seconds
  3. Device restarts automatically
  4. Default settings have been restored

The unit will reboot automatically. Once the power light stops blinking, the unit has been reset and is ready to use. Resetting the router does not reset the firmware to an earlier version, but it will change all settings back to factory defaults.

PLDT SpeedSurf 504AN Router Security

Change PLDT SpeedSurf 504AN Default Wifi Name (SSID)

Rename your PLDT SpeedSurf 504AN Default Wifi Name (SSID). Some PLDT routers come with default network names (with the name of the manufacturer). We recommend to use a different name because a default name unnecessarily identifies the make of your router, making it easier for attackers to break in.

Change PLDT SpeedSurf 504AN Default Password

It’s easy for a hacker to find out the manufacturer’s default password for your PLDT SpeedSurf 504AN router and then use that password to access your wireless network. So it’s wise to change the administrator password for your PLDT SpeedSurf 504AN router. When you’re deciding on your new password, try to pick a complex series of numbers and letters and try to avoid using a password that can be guessed easily.

MAC Address filtering for PLDT SpeedSurf 504AN router

MAC filtering allows you to limit access to your PLDT SpeedSurf 504AN router. To enable this feature, enter into your PLDT SpeedSurf 504AN router the 12-character MAC ID of each computer that will connect to your network. Be sure to update this information if you add or remove devices.

Disabling Broadcast SSID for PLDT SpeedSurf 504AN router

PLDT SpeedSurf 504AN router transmits your Wi-Fi network ID (the so-called SSID) to everyone. This may be changed at will by unchecking the corresponding box in the settings. Then your network will not be so easily hacked. However, as a compromise, you will have to enter the SSID every time that you connect a device to the network. This step is not mandatory.

MAC Address filtering for PLDT SpeedSurf 504AN router

MAC filtering allows you to limit access to your PLDT SpeedSurf 504AN router. To enable this feature, enter into your PLDT SpeedSurf 504AN router the 12-character MAC ID of each computer that will connect to your network. Be sure to update this information if you add or remove devices.

Where are you placing the PLDT SpeedSurf 504AN router in the house?

You wouldn’t think about this at first, but where you place your PLDT SpeedSurf 504AN also has a bearing on your security.

Place the PLDT SpeedSurf 504AN router as close as possible to the middle of your house. The first benefit is that all the rooms in your house have the same access to the Internet. The second benefit is that you don’t want to have your wireless signal range reach too much outside your house, where it can be easily intercepted by cybercriminals.

For this reason, don’t place your PLDT SpeedSurf 504AN router next to a window, since there’s nothing to obstruct the signal going outside your house.